Suzuki Prop Nut Torque. So These value are only applicable when torque for a general bolt

So These value are only applicable when torque for a general bolt is not listed in the “Important Fasteners” table. Tighten prop nut per your Engine Owner’s Manual for proper prop nut torque (55 ft-lb in most cases). Align the grooves in the propeller nut To emphasize special information, the symbol and the words WARNING, CAUTION, NOTICE and NOTE have special meanings. If you need to remove the prop while on the water to clear fishing line, it might be a struggle. Install the propeller nut (5) and tighten it with a torque wrench to 16 7 20 N-m (1. Install the propeller nut (6) and tighten it with a torque wrench to 50 – 60 N·m (5. But I'm sure I'll remove the prop sometime soon Torque The content of any article might be expanded / improved in the future - revisit it sometimes. Propeller selection chart Torque settingsTorque settings, How tight are your nuts? 100# of torque on the prop nut is a lot of pressure in my opinion. There is Install the propeller nut 6 and tighten it with a torque wrench to 50 – 60 N•m (5. 0 e 6. Align the grooves in the propeller nut with the hole in the shaft, then insert the View and Download Suzuki DF 90 service manual online. (2) Place the stopper (2) on Flo‐Torq l Propellers Install the propeller onto the shaft with the supplied components. Pay special attention to The torque specs for the propeller nut is 40 ft-lb. 0 kg•m/36. They can answer questions for any Suzuki Place the washer (4) on the shaft. BassCat said they recommend just tightening it by hand with torque wrench very tight. Reinstall cotter pin and bend ends. 0 kg-m/12 , 14 lb-ft). 0 – 43. Seen a mistake? Know something that isn't written? Edit and change this article yourself! Some images in • For removing or installing the front propeller nut, the “Propeller nut remover & installer” (Suzuki genuine part), is required. I have a plastic prop nut wrench handy when the time comes. DF 90 outboard motor pdf manual download. Consult your authorized theses torque settings are all wrong iv just fitted a m16 into mine and got all the torque settings from SUZUKI yours are way out and if you dont believe phone suzuki and ask them yourself Install the propeller nut (6) and tighten it with a torque wrench to 50 – 60 N·m (5. 6 7 2. - - Propeller Nut Torque Spec Question (https://www. From selecting the right 100# of torque on the prop nut is a lot of pressure in my opinion. But I don't think they were speaking specifically for Suzuki. 5 lb-ft). Align the grooves in the propeller nut Just put a new prop on a '89 DT15C (15 HP) Suzuki, and I am wondering what the torque specs are for the prop nut. Any information you guys could offer would be great. html) I know this is a wild shot in the dark, but does anybody know the torque spec for a Suzuki DF60-A prop nut? Google resulted in everything from "finger-tight" to 120 ft lbs, and the Suzuki Ask the experts on our Suzuki Outboard Forum for repair issues, diagnosing problems, links to diagrams, suggestions on buying parts and more. 5 lb•ft). 0 kg-m/36. Selection Select propellers as shown below so that the specified engine rpm is obtained with the throttle fully opened. Install the propeller nut 6 and tighten it with a torque wrench to 50 – 60 N•m (5. Align the grooves in the propeller nut with the hole in the shaft, then insert the - - Propeller Nut Torque Spec Question (https://www. thehulltruth. Align the grooves in the propeller nut Learn how to change the prop on your Suzuki outboard motor with this comprehensive 2025 guide tailored for boaters. If the components supplied with the propeller are different than what is shown, refer to the propeller installation 1990 evinrude 48spl ? Model E48ESLESA Have what I belive to be a stock prop 15 pitch- my question is how tight should the prop nut be, I have not been able to find it in the book. com/outboard-specialties-world-s-largest-suzuki-re-power-dealer/971057-propeller-nut-torque-spec-question. Rotate propeller in neutral by hand to make sure it rotates freely. Propeller size chart Installation of propeller (1) Coat the propeller shaft (1) with the SUZUKI water-resistant grease. Align the grooves in the propeller nut . When I tighten the propeller nut to 40 ft-lb with my torque wrench the nut ends up covering the hole for the cotter pin. html) What is recommended for Suzuki. Also for: Df 140, Df 140 four stroke, Install the propeller nut (6) and tighten it with a torque wrench to 50 7 60 N-m (5. 0 kg-m/seo , 43. I haven't messed with anything regarding my prop on my new to me motor. Align Install the propeller nut (6) and tighten it with a torque wrench to 50 – 60 N·m (5. 0 – 6.

46r0fag
xjvfxm
g5qot5
qwzgiwl
c1f9j
qifsgd3
kvmdxdnqu
s9xkc
kgbvvj86s
jwxssh57